Cutting Board with a Breadboard Edge

Last weekend I had some Eastern White Pine scraps lying around after I finished building a display cabinet for my wife for her spring show which just got cancelled due to the COVID-19 virus. I hate to throw the scraps away or toss them into the fire pit so I decided to make a small cutting board with them.

I ripped two of the boards 3″ wide and glued up the pieces. The third piece I ripped to 1 1/2″ wide which would serve as the breadboard ends,

After the glue dried, I sized the board to 16 1/2″ long by 12″ wide. I set up my table saw blade at 1/4″ tall with the furthest part of the blade 3/4″ from the fence using my little Odd Jobs ruler.

I cut grooves on the top and bottom of each end to create a 1/4″ by 3/4″ tenon across the board. I then cleaned up the rough marks with a chisel and rabbet plane so I would have a nice smooth tenon on each side of the board.

Then I took the two 1 1/2″ wide boards and ran a 1/4″ groove 3/4″ high down the edges to give me a nice groove that would be snug with the tenons.

I marked where I wanted the pins to go through the tenon and drilled through the breadboard ends with a 1/4″ drill bit. Then I took the ends and marked with the drill bit where the pins would intersect the tenon. Being this cutting board is small and the sides of the breadboards fit nicely with the tenon, I didn’t bother draw boring the joint.

I then drilled the holes and elongated the holes at each end with a round rasp to allow for seasonal movement as the wood will expand and contrast with changes in humidity.

I applied a little glue only in the center of the tenon, clamped and drove 1/4″ walnut dowel pins through all six holes.

After the glue dried, I cut the pins flush and sanded the surface up to 220 grit sandpaper. Then I trimmed the breadboard ends flush to the sides of the cutting board and sanded the edges.

I applied a couple coats of my black shellac I made to give it an aged look. I think the board came out a little too green in color, but my wife Anita likes it. She said it makes it look old and worn. It turned out to be a quick and easy project on a Sunday afternoon.

Whipping Up a Reclaimed Tray

Last week, Anita came home from Home Goods with a tray that she bought for $18.00. I took a look at it and thought to myself ” I coulda made that, but whatever”. Well, after she had it on our dining room table she decided that the sides of the tray were too high and asked me to make her one with shallower sides.

20180603_143612-e1528333925315.jpg

I went into the basement and looked in a box that I filled with wood that came from an old pallet I tore apart. I know using pallet wood is frowned upon in the woodworking world, but it was free and has the character Anita was looking for.

20180603_093417.jpg

The first thing I did was grab a few pieces and planed them down only on one side to make them about 3/8″ thick. I then milled the boards to 3″ wide and glued them together. I used two old panel clamps that I bought last year at an antique show that excel at gluing thin boards together.

IMG_20180603_094127_832.jpg

The bars on each side prevent the boards from buckling up when clamping pressure is applied. I originally bought the clamps to sell them to make some quick cash, but I’m glad I never did. They work great!

IMG_20180603_094127_826.jpg

After the glue dried, I sanded the planed side on my Performax drum sander to make the bottom of the tray perfectly flat.

20180603_113135.jpg

Anita wasn’t thrilled with the gray color of the wood, so I used my Porter Cable Restorer and sanded the gray off the panel perpendicular to the grain. This allowed the wood to get cleaned up yet not lose its character.

IMG_20180603_120625_532.jpg

After the panel was sanded, Anita applied Weathered Oak stain to the pieces. You can see how the stain pops the grain, but still makes it look old.

IMG_20180603_120625_533.jpg

After the stain dried, I glued and nailed the sides to the bottom. The sides are 1 1/2″ wide x 1/2″ thick reclaimed pine.

20180603_143335.jpg

Anita installed some blacksmith made handles to the sides and placed it on our dining room table. A super quick and easy project that was made within just a few hours.

IMG_20180605_193110_851.jpg

Resizing another Shelving Unit

I was in the process of building another shelving unit for my wife’s new booth in Milford, Ohio. She originally asked me to build it four feet long. However, once I started to attach the shelves to the unit, she wasn’t too thrilled with the overall dimensions. I asked if she wanted it cut down to 36″ long instead of 48″, but she was afraid that it would be too much work. I assured her that I could cut it down without much problem.

20170916_143343.jpg

I slapped the unit on top of my workbench and carefully measured where the rails were to be cut. I then grabbed my Festool plunge saw and rail system, clamped it to the lines and ran down the rail cutting as deep the blade would go.

20170916_145039.jpg

I then flipped the unit off the bench and cut the two attached shelves in half.

20170916_145418.jpg

After one side was free, I unscrewed the pocket holes and broke away the rails with a hammer. I then cleaned the side up with a random orbital sander.

20170916_145846.jpg

I then flipped the other side of the unit back onto the bench and re-drilled the pocket holes to the shortened rails. For the two shelves that already had plywood nailed in place, I had to bust out the plywood with a hammer.

20170916_151515.jpg

After about twenty minutes, the shelving unit came back together a foot shorter. I cut the remaining plywood to the new measurements and installed them using cleats on the inside of the rails.

20170916_153255.jpg

Now it was time for the antique shutters to be screwed onto the sides.

20170916_184259.jpg

After a coat of black paint, the shelving unit looks really nice in her new booth.

20171012_202337.jpg

Making Floating Shelves

My wife, Anita wanted me to make some custom floating shelves for the dining room. We had some floating shelves from Ikea, but she wanted something that would match the coffee bar I made her.

Making the shelves were super easy. I grabbed 3/4″ pine and a couple of 2 x 2 select pine from Home Depot. I made the width of the shelves 3 1/8″ thick so that the 2 x 2 would fit inside nicely without getting jammed inside.

20170813_135623

I used my miter jack to make sure the sides were a perfect 45 degrees so all the pieces would fit nicely together with no gaps. Most people make these shelves with simple butt joints on the ends, but I didn’t want end grain showing so I took the time to miter the corners.

20170813_135638

After making sure everything fit together well, I glued and clamped the whole assembly together.  Anita then stained the shelves with apple cider vinegar, steel wool solution and gel stain to match the coffee bar.

20170813_144147

When it came to install the shelves, I attached the 2 x 2 frame to the wall by securing it to the studs making sure it was level.

20170822_203058\

I then slid the shelf into place and secured it in place from the bottom into the 2 x 2 frame.  I then did the exact same thing on the second shelf.

20170822_203808

Here are the shelves installed with a bunch of Rae Dunn pottery on them. Anita was planning on writing messages on the chalk board wall to give it some pizzazz, but decided the wall is too dark and will eventually paint it back normal. What do you think? Should she give the chalk board wall a shot with fancy chalk board writing on it?

20171010_095354.jpg

She painted the wall.

20171017_170847.jpg

Big Ole Wood Shelf

Several months ago, I started making a shelving unit out of southern yellow pine that my wife asked me to make for her booth. I got this far and it sat in my shop unfinished for months. After much contemplation, my wife and I both realized that the shelving unit was really too big to fit in our Ford Edge.

20170722_120716.jpg

The best thing we could do, is take it apart and resize the thing smaller so we wouldn’t have to rent a trailer to transport it. Luckily, I put the shelf together almost entirely with pocket screws. The part that was glued, I cut apart on the band saw.

20170722_122654

After, I cut the shelves shorter, I used my router and cut floating tenons on all the pieces instead of using pocket holes screws like I did before.

20170722_131434

A few hours later, I had the new resized shelving unit put back together. The height stayed the same at five feet, but the length was cut down from five feet to forty inches so that it would fit in our car.

20170722_171943

My wife always wanted the unit to roll so I added four old casters to the bottom. We actually bought the casters many months before we decided to make the shelving unit just in case someday we needed them.

20170723_100917

With 1/2″ plywood installed for the shelves, the unit was built, but unfinished.

20170723_102601

Anita wanted the unit to look somewhat old, so I smacked the wood around with a hammer and crowbar to give it an aged look.

20170723_123747

I bought a few piece of thin gauge metal, drilled some holes in it, bent it over in my vise, painted them black, and screwed them to the corners of the shelving unit to give it a more industrial look. The brackets and the dark stain really makes the unit pop. Now it was ready to throw in the Edge and bring it to our booth. Saved us $50 not having to rent a trailer and we both feel it looks nicer then it did before.

IMG_20170812_133702_428

 

Everyday Console Table

I call this piece the “everyday table” because you see this design everyday. I spotted this one at Home Goods just last week. It’s kind of a cross between a table and a bookcase. As far as construction goes, it’s very simple. Six framed legs with a top, a couple of shelves and a cross “X” on each side. In fact, there’s a website that shows how to build this table, pocket screws and all.

20170709_141125

Say what you want about the design and construction, but they are very popular and super easy to build. My wife found the website the other week and asked me to customize one to fit in our dining room as a coffee bar.

20170604_153948

Being true to form, I built ours out of southern yellow pine (2 x 10’s). I wasn’t a fan of the thick 2 x 4 legs so I milled all the parts down to 1″ thick.

img_20170605_111353_327

Keeping it simple, I used pocket screws and glue to attach all the pieces. The shelves are southern yellow pine boards I ripped and glued back together to create a quarter sawn panel so they wouldn’t expand and contract too much.

20170604_140643

The hardest part about building the piece are the X’s on the sides, but all that entails is cutting a couple of half lap joints.

20170604_141457

Here is the finished bar with a vinegar steel wool solution and gel stain on top to give the wood some depth. The coffee bar has turned more into a display table for my wife’s Rae Dunn collection, but that is another story for another day.

20170717_205426

I have since played around with the design again and built another one using eastern white pine. Construction is similar except I used floating tenons instead of pocket screws to build the frames. I’ll still use the vinegar and steel wool solution again on this one and stain it a dark color. My third design will probably have a thicker top and I may use plywood for the shelves. Stay tuned.

20170716_173034

 

 

Inexpensive Window Trim

The windows in our house aren’t much to talk about. Just 36″ square vinyl windows in a typical ranch. I’m not sure how old they are as I know they aren’t original to the house, but were here when I bought it fifteen years ago. My wife, Anita, wanted to jazz them up a bit and give them some character, so she asked me to make trim to go around them.

20170312_105920

The first thing we did, was to take out the marble sill, which was the hardest part. Sometimes they get stuck inside the frame, so I had brake them apart in order for them to come loose. If I was lucky, I could cut the sealant around the sill and jimmy it loose.

20170312_105942

I made a new sill out of 7/8″ thick maple. I tried to get rift sawn material so it wouldn’t warp too bad. I cut notches on both sides of the sill so it would stick out on the wall so the 1×4’s could lay on top of it.

20170312_123610

We wanted the header to have character so we took a 1×6 of pine and attached a 1×2 on the top. We then laid a cove molding on the 1×6.

20170312_1235571

Using my small miter box, I was able to cut the tiny pieces of cove for the ends.

20170318_122351

I then took a piece of pine 1/2″ thick and used my block plane to shape the corners and ends to create a bullnose. I pinned everything together  with my 18 gauge pneumatic nailer to complete the header.

img_20170312_142516_891

Back at the window, I measured, cut, and nailed the rest of the pieces to the wall using a 15 gauge finish nailer. I trimmed the maple sill so that there would be a 3/4″ overhang to sides on both ends.

img_20170312_202015_986

Here’s the close up of the header nailed to the wall. The 1/2″ thick bullnose hangs over 1/2″ on both sides of the frame.

20170323_203246

After filling the nail holes with putty, Anita caulked, primed, and painted the window trim. We did both windows in our bedroom the same way. The next step is to frame around the closet, paint the room, get a new headboard, new blinds, ceiling fan, rug, etc… I don’t know, ask Anita, she’s the designer. haha